對于中小型電機，常見的軸伸有兩種，即圓柱型的圓錐型；仔細觀察可以發現，起重冶金用電機一般采用圓錐軸伸，而其他負載電機大部分為圓柱軸伸。

圓錐形軸伸截面直徑是變化的，這樣軸伸根部所承受的扭轉剪應力要比直軸好很多，不容易因交變應力造成金屬疲勞而斷軸，因此適用于大載荷、高慣量、頻繁正反轉的機械設備，起重冶金電機選擇錐軸伸也就不言而喻了。

我們YZ、YZR和YZP系列等用于起重冶金設備的電機，大多數是采用錐軸伸，與普通的圓柱軸伸相比，錐軸伸的加工及檢測要相對復雜一些，特別是對于采用普通車床加工軸時，對操作工的技能要求較高，而采用數控車床加工時，這個問題就迎刃而解了。

如何檢測錐形軸伸？

電動機軸伸屬重要的安裝尺寸，如果加工不合格，會影響與主機的聯結效果，不能有效傳遞轉矩，甚至使設備產生振動，如何檢查電動機軸伸尺寸很重要。

對于圓錐軸伸，測量普通軸伸的外徑千分尺顯然是不可以的，為了解決該問題，通常采用專門的量規進行測量，即我們通常所說的圓錐環規。圓錐環規是檢驗圓錐形軸伸直徑、錐度及長度的專用綜合量具。

該環規的特點是一種規格的軸伸對應一種專門的量具，無論錐度、直徑及長度有任何的差別，都沒有通用性；采用錐度環規檢查，實際上是檢查兩者的配合關系，常規的做法是在軸伸上沿軸向涂以鉗工用紅丹粉，而后將環規套入，將兩者軸向配合到位后，旋轉環規一周以上，而后檢查涂料的受磨合狀態，以?xún)烧呙芎厦娣e超過70%作為判定合格的依據。

For small and medium-sized motors, the most common types of shaft extensions are cylindrical and conical; Upon careful observation, it can be observed that motors for lifting and metallurgy generally use conical shaft extensions, while most other load motors use cylindrical shaft extensions.
The diameter of the conical shaft extension section varies, so the torsional shear stress borne by the root of the shaft extension is much better than that of the straight shaft, and it is not easy to break the shaft due to metal fatigue caused by alternating stress. Therefore, it is suitable for mechanical equipment with large loads, high inertia, and frequent forward and reverse rotation. It is self-evident to choose conical shaft extension for lifting and metallurgical motors.
The motors commonly used in lifting and metallurgical equipment, such as the YZ, YZR, and YZP series, mostly use conical shaft extensions. Compared with ordinary cylindrical shaft extensions, the processing and inspection of conical shaft extensions are relatively complex, especially when using ordinary lathes to process shafts, which require higher skills from operators. However, when using CNC lathes to process shafts, this problem is easily solved.
How to detect conical shaft extension?
The motor shaft extension is an important installation dimension. If the processing is not qualified, it will affect the connection effect with the host, cannot effectively transmit torque, and even cause equipment vibration. It is important to check the motor shaft extension dimension.
For conical shaft extension, it is obviously not possible to measure the outer diameter of a regular shaft extension with a micrometer. To solve this problem, a specialized gauge, commonly known as a conical ring gauge, is usually used for measurement. Cone ring gauge is a specialized comprehensive measuring tool used to test the diameter, taper, and length of a conical shaft extension.
The characteristic of this ring gauge is that one specification of shaft extension corresponds to a specialized measuring tool, and there is no universality regardless of any differences in taper, diameter, and length; The use of a taper ring gauge for inspection is actually to check the fitting relationship between the two. The conventional practice is to apply red lead powder for fitters along the axial direction on the shaft extension, then insert the ring gauge, fit the two axially, rotate the ring gauge for more than one turn, and then check the wear in status of the coating. The judgment of qualification is based on the fact that the fitting area of the two exceeds 70%.