與作為 IEEE 802.3 規范演變的基礎的令牌環網絡不同，實際上禁止將以太網配置為真正的環。以太網中的任何循環都將導致在無限循環中轉發的數據包重復，從而迅速降低網絡的帶寬和效率。沒有專門處理以太網環管理的可用通用標準。專有的網絡市場解決方案提供產品差異化和各種技術可用于網絡環管理的實施。然而，在尋找基于標準的環管理解決方案時，生成樹或快速生成樹協議可能符合要求。

生成樹協議 (STP) 在 IEEE 802.1d 中定義，通過阻止重復鏈接在任意兩個網絡節點之間形成單個活動路徑，在以太網交換機的網狀網絡中創建“生成樹”。如果任何活動鏈路發生故障，網絡中的冗余可以提供自動備份路徑。

冗余鏈路的這種管理對于減少工業網絡的停機時間是非?？扇〉?。例如，圖 2 中所示的網絡包含鏈路 2、3、4 和 5 之間的環路。這里 STP 將強制這些鏈路之一進入阻塞狀態以中斷環路。在這種情況下，鏈路 4 被阻塞，然后可以充當備用鏈路。如果任何其他活動鏈路 2、3 或 5 隨后發生故障，協議將禁用阻塞狀態以啟用交換機之間的完全連接。請注意，在此示例中，鏈路 1 沒有冗余備份。

STP 由網絡中的每個交換機定期交換網絡狀態信息，每兩秒進行一次。此信息在稱為網橋協議數據單元 (BPDU) 的特殊數據包中承載，由以太網多播地址 01:80:C2:00:00:00 標識。協議的運行分為三個階段：

選舉根交換機；

查找到根交換機的所有路徑并確定“成本低”的路徑；

我司產品廣泛應用于數控機械 冶金,石油天然氣,石油化工，
化工,造紙印刷,紡織印染,機械,電子制造,汽車制造,
塑膠機械,電力,水利,水處理/環保,市政工程,鍋爐供暖,能源,輸配電。

Unlike a token-ring network, which has been the basis for much of the IEEE 802.3 specification evolution, it is in fact forbidden to configure Ethernet as a true ring. Any loops within an Ethernet network will result in the duplication of packets that are forwarded in endless loops, quickly degrading the bandwidth and efficiency of a network. There is no available common standard that specifically deals with the management of Ethernet rings. Proprietary network market solutions provide product differentiation and various techniques can be used for the implementation of network ring management. However, when looking for a standards-based solution for ring management, Spanning Tree or Rapid Spanning Tree Protocol may fit the bill.

Spanning Tree Protocol (STP) is defined in IEEE 802.1d and creates a ‘spanning tree’ within a mesh network of Ethernet switches by blocking duplicate links to form a single active path between any two network nodes. The redundancy in the network can provide automatic backup paths if any of the active links fail.

This management of the redundant links is very desirable to reduce the down time industrial networks. For example, the network shown in Fig. 2 contains a loop between links 2, 3, 4 and 5. Here STP will force one of these links into a blocked state to break the loop. In this case link 4 is blocked, which can then act as the backup link. If any of the other active links 2, 3 or 5 subsequently fail, the protocol will disable the blocked state to enable full connectivity between the switches. Note in this example there is no redundancy backup for link 1.

STP is conducted by each switch in the network regularly exchanging information on the status of network, every two seconds. This information is carried in special data packets called Bridge Protocol Data Units (BPDUs), identified by the Ethernet multicast address 01:80:C2:00:00:00. There are three stages of operation of the protocol:

Electing a root switch;

Finding all paths to the root switch and determining the ‘least cost’ paths;